Ghost 2 Immobiliser Reviews
The ghost 2 immobiliser is a cutting-edge anti-theft device that makes use of advanced technology to prevent car theft. This discreet device is undetectable by thieves, and it only starts your engine when a PIN code or app is entered.
It's weatherproof and connects to the CAN data network of your vehicle. It has a service/valet function that lets you temporarily start your vehicle while it is in garage.
Easy to install
The Ghost immobiliser protects your car from key theft as well as hacking, cloning and stealing. It is a PIN code system that is integrated into your car's electronic control unit, making it hard for thieves to detect. It's not noticeable and does not use sensors or special keys. It's also less expensive than replacing an ECU, or installing a key fob. It can even lower your insurance premiums.
When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's directions carefully. This will ensure that the device operates properly and efficiently. After the installation is completed check the system by entering the PIN code, then turning on the engine. Regular testing will enable you to spot any issues early.
Before starting the installation, double-check the position of the CAN H and CAN L wires. They are crucial to power the immobiliser, so it is vital that they are connected correctly. It is also an excellent idea to label the wires so that it makes it easier to locate them when installing the device. Once you've identified the location of these wires, connect them to a constant 12V power source as well as an earthing point. Make sure you utilize a fuse tap if required to shield the connections from short circuits or damage.
After connecting the wires, neaten the wiring with cable ties to prevent tampering. It is also a good idea to cover the wires with insulation tape or heat shrink tubing. This will shield them from electrical shorts and increase the life span of the device. Once the wiring is secure it's a good idea test the Ghost 2 immobiliser.
In the event that you have to surrender your vehicle, such as for servicing or valet parking for valet parking, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. Press the brake pedal, and hold the accelerator for a number of times equal to the number one in the emergency code. The system will then enter service mode. This can be confirmed by flashing 5 times the indicator signal.
Change PIN codes easily
Ghost 2 immobilisers are an excellent method of protecting your vehicle from theft. It is installed discreetly within the vehicle, and is only accessible by a special code. The device is directly connected to the vehicle ECU through its data bus, and does not rely on radio frequency signals, as do traditional Thatcham immobilisers or other aftermarket alarm systems. This makes it difficult for thieves to listen for the click of an immobiliser relay or to install new key fobs. The control unit is hidden in the vehicle's wiring or dashboard, and can't be physically tampered to reset the system.
The ghost 2 immobiliser is connected to your vehicle's CAN Data network and uses the buttons already present on the steering wheel, door panels and the centre console to create an individual sequence of up 20 button presses. These must be entered before the engine can start - just like the PIN code. This innovative next-generation system does not require cutting of wires when it is installed and is fully reprogrammable at anytime. You can even put your vehicle in Valet or Service mode to allow it to be started temporarily while you are giving it to a mechanic to work.
You can also make use of the app to change your PIN code or disable it completely if you have lost your keys. This feature is particularly useful if you've given your car to someone else to use for valet service or parking. It prevents them from starting the car and driving it away without your consent. It is also undetectable by professional thieves, as it doesn't utilize circuit cuts or radio frequencies.
Another great feature of the ghost 2 immobiliser is its ability to stop relay thefts. Relay theft is a typical method of car theft in which criminals attack the diagnostic port on your car and alter the signal that is sent by the key to the vehicle's ECU to trick it into believing that there is a valid key. The traditional immobiliser can be manipulated in this manner, however with the ghost 2 immobiliser, the signal is blocked by the immobiliser before it gets to the ECU.
Simple to use app
Ghost 2 is a revolutionary immobiliser that shields your vehicle from key-cloning, hacking and key theft. It connects to the CAN data network of your vehicle and requires an PIN code to start the engine. It also prevents thieves from using signal spoofing and device spoofing, both of which are common methods used to steal vehicles.
The system is simple to use and operates similar to a standard car alarm. After installing it, you can generate an individual PIN code sequence that is up to 20 digits long, which will have to be entered before the vehicle starts. This will stop the vehicle from being taken even if your keys get stolen. If you want to deactivate the system it is possible to do this by using an app on your smartphone.
Unlike other systems it is completely silent and does not emit any radio frequency signals. It is a weatherproof, discreet device that can be installed anywhere in your vehicle. It can be hidden under the dashboard, door panels or the steering wheel. It communicates via the CAN data loop with your ECU and is not affected at all by diagnostic tools used by thieves to find security systems. It is not affected by jamming devices which can spoof codes.
It is a hidden system that can be used to prevent theft from all vehicles. Its technology has been proven be effective and in compliance with TASSA standards. The Ghost is a fantastic choice for classic or sports cars. It can also be used as a way to protect vehicles being rental on apps such as Turo.
The Autowatch Ghost 2 is the next generation of vehicle immobilisers. autowatch ghost 2 immobiliser is unnoticeable to thieves and blocks them from starting your vehicle unless they have your PIN or have been authorized by the app. It also doesn't emit radio frequencies or other signals that can be detected by scanners. The installation process is easy and quick. The app comes with a simple interface and a simple navigation. It also includes a GPS tracker that can help police locate the vehicle and recover it.
Easy to reset
A ghost 2 immobiliser is a great way to protect your vehicle from theft. It connects to your vehicle's ECU to create a wall that thieves are unable to break through without a valid PIN. The device is TASSA verified that means it's recognized by insurance companies. It's a great tool to deter theft of your car and can save you money in the end.
The Ghost system unlike traditional alarms and immobilisers that require cutting of circuits it is directly connected to the vehicle's CAN data network. It works through the buttons on your dashboard and steering wheel. You can create a unique PIN that is up to 20 presses long. This PIN has to be entered before the engine can start the same way as the credit card PIN. Ghost is inaccessible to thieves, and there are no LED indicators to give away its presence, which makes it the most efficient aftermarket CAN bus immobiliser that is on the market today.
The Ghost system has another advantage that it does not transmit radio frequency signals. This means it is not detected by thieves or snatched up. This prevents relay attacks and keys that are cloned as well as the more usual method of hacking a car's CAN bus system by looking for signals from its alarm/immobiliser. The Ghost system is designed in a way that it can be hidden within your vehicle. There aren't any LEDs or other signals to signal its presence.
The system has the option of a Transport Mode that disables the Ghost System. This is useful in situations where you may require a temporary deactivation of Ghost for instance, when transporting or servicing your vehicle. However this mode isn't as efficient as Service Mode, as it does not turn off the Ghost system if your vehicle is traveling over 31 mph for fifteen minutes.
You will need the emergency code from your installer to reset your Ghost 2 immobiliser. It is usually hidden under an area for scratch-offs on the card that was supplied with your installation. It is important to keep this emergency code safe and keep it in a location that is secure, like your wallet at home.